With this guide, you’ll discover how to properly clean your ZeroWater Filter to ensure optimal performance!
ZeroWater is a brand of water filter that is designed to remove impurities and contaminants from tap water.
The ZeroWater filter uses a unique 5-stage filtration system that claims to remove 99.6% of all dissolved solids from tap water, including lead, chromium, mercury, and chlorine.
The company claims that its filters are more effective than traditional carbon-based filters and that they can provide better-tasting, cleaner water for drinking, cooking, and other uses.
However, over time, these filters can become clogged with impurities, which can affect their performance. Regular cleaning is therefore essential to maintain the filter’s effectiveness.
Zero Water Filter Maintenance – Cleaning Like a Pro
Cleaning the Zero Water Filter may seem complicated, but with the appropriate methods, it is a quite simple process!
- Large Bowl or Container
- White Vinegar
- Warm Water
- Soft-Bristled Brush
- Clean Towel or Paper Towel
Time needed: 30 minutes.
To clean your Zero Water filter, follow these simple instructions:
- Disassemble the Filter
Before you begin cleaning, you will need to disassemble the filter.
Start by removing the filter from the pitcher or dispenser. Next, remove the filter’s cap and take out the filter cartridge.
- Soak the Filter Cartridge
Fill a large bowl or container with enough white vinegar to fully submerge the filter cartridge.
Place the cartridge in the bowl and allow it to soak for at least 30 minutes.
This will help dissolve any buildup or impurities in the filter.
- Clean the Filter Cap
While the filter cartridge is soaking, use warm water and a soft-bristled brush to clean the filter cap.
Pay special attention to any nooks or crannies where buildup can accumulate.
- Rinse the Filter Cartridge
After the filter cartridge has soaked for at least 30 minutes, remove it from the vinegar solution and rinse it thoroughly under running water.
Use the soft-bristled brush to gently scrub away any remaining buildup.
- Reassemble the Filter
Once the filter cartridge is clean and rinsed, reassemble the filter.
Put the cartridge back into the filter cap, then screw the cap back onto the pitcher or dispenser.
- Run Water Through the Filter
After reassembling the filter, run water through it for a few minutes to flush out any remaining vinegar or debris.
This will ensure that your water tastes fresh and clean.
That’s it! Now you have a clean Zero Water filter.
Regularly cleaning your Zero Water filter is essential to maintain its efficiency and ensure you get the cleanest, purest water possible.
By following these simple steps, you can keep your filter in excellent condition and enjoy fresh, contaminant-free water for a long time to come.
Remember, a clean filter means a healthier you!
Frequently Asked Questions
Some frequently asked questions regarding cleaning your Zero Water Filter are included below!
The frequency at which you should clean your ZeroWater filter will depend on your usage and the quality of your tap water.
As a general guideline, it is recommended to clean your ZeroWater filter at least once a month or after filtering approximately 40 gallons of water.
However, if your tap water is particularly hard or contains a high concentration of minerals and contaminants, you may need to clean your ZeroWater filter more frequently.
You can also monitor the TDS (total dissolved solids) meter on your ZeroWater pitcher or dispenser to determine when it’s time to clean the filter.
ZeroWater filters have an expiration date, after which they may not work effectively. If your filter is expired, replace it with a new one.
Sometimes, new filters can have a slightly musty smell due to the carbon used in the filtration process. Try running several cycles of water through the filter, as well as rinsing it thoroughly with cold water.
If the odor persists, you can try soaking the filter in a solution of one part white vinegar to three parts water for several hours. Then rinse it with cold water before using it.
I do not recommend using bleach to clean your ZeroWater filter. Bleach is a strong chemical that can damage the filter and compromise its ability to remove contaminants effectively.
Instead, the best way to clean your ZeroWater filter is by soaking it in a solution of water and white vinegar.
If you prefer not to use vinegar, you can also clean the filter with a mild soap and water solution.
No, it is not recommended to clean ZeroWater filters in the dishwasher.
ZeroWater filters are not dishwasher safe and may become damaged or broken if exposed to high temperatures and harsh detergents in the dishwasher.